Pre-Assembly
Unpacking
- Read all instructions before assembling.
- Assemble and operate the stairclimber on a hard, level surface in the area intended for use.
- Attach all fasteners and partially tighten them. Do not fully tighten fasteners until assemble of all components is complete.
- Do not attempt to move the unit by yourself. Have at least one other person help and use safe lifting techniques.
- Do not grasp on any plastic parts of the unit while lifting and moving. The plastic components are non-structural covers and not capable of supporting the weight of the unit.
- Locate the hardware package. The hardware is labeled with its specification as a description. Each of the assembly steps reference the descriptions to avoid confusion during assembly.
Tools and Parts Included
Tools Included |
5mm Allen Wrench |
6mm Allen Wrench |
Parts Included |
Quantity |
Part Name |
1 |
Main Frame |
1 |
Console |
1 |
Console Mast |
1 |
Column Group |
1 |
Decorative Ring |
1 |
Handlebar Group |
2 |
Side Handlebar |
2 |
Decorative Ring |
1 |
Handlebar Reinforcement |
1 |
Hardware Kit |
2 |
Handlebar Cover |
CSC900 Step-by-Step Assembly
1. Console Mast and Main Frame
Hardware Needed for This Step |
TYPE |
DESCRIPTION |
QUANTITY |
Console Mast |
|
1 |
Bolt |
M8 x 20L |
1 |
Bolt |
M6 x 65L |
1 |
Bolt |
M8 x 55L |
3 |
Washer |
8 |
5 |

a. Insert the console mast wire through decorative ring then around to insert through rear of tube. Connect the communication wires between the main frame and console mast.
b. Attach the decorative ring to console mast using the bolt M8*20 (1pc), M8*65 (1pc) and ø8 flat washer (2pc).
c. Attach the column group to the lower main frame, using the M8*55 bolts (3pcs) and the ø8 flat washer (3pcs).
2. Step Base
Hardware Needed for This Step |
TYPE |
DESCRIPTION |
QUANTITY |
Step Base |
|
1 |
Bolt |
M8 x 20L |
2 |
Bolt |
M8 x 30L |
1 |
Washer |
8 |
2 |

a. Attach the step base to the lower main frame using the M8*20 bolts (2pcs), ø8 flat washers (2pcs) and M8*30 bolt (1pc).
3. Handlebars
Hardware Needed for This Step |
TYPE |
DESCRIPTION |
QUANTITY |
Side Handlebars |
|
2 |
Handlebar Group |
|
1 |
Decorative Rings |
|
2 |
Reinforcement Plate |
|
1 |
Bolt |
M8 x 20L |
6 |
Bolt |
M8 x 40L |
2 |
Washer |
8 |
6 |

a. Connect wires with same terminal.
b. Attach the side handlebars to the handlebar group and with the decorative rings using M8*20 bolts (4pcs), ø8 flat washers (4pcs).
c. Attach the handlebar group to the console mast with the reinforcement plate using M8*40 bolts (2pcs), ø8 flat washers (2pcs).
d. Attach the handlebars to the column groups using M8*20 bolts (2pcs).
4. Console
Hardware Needed for This Step |
TYPE |
DESCRIPTION |
QUANTITY |
Console |
|
1 |
Handrail Covers |
Sets |
2 |
Bolt |
M8 x 20L |
4 |
Screw |
M4 x 30L |
4 |
Screw |
ST4.2 x 15L |
2 |

a. Connect the console using M8*20L bolts (4pcs).
b. Secure the handlebars on each side using ST4.2*15L screws (2pcs).
c. Attach the handrail covers on each side using M4*30L screws (4pcs).