Pre-Assembly
Unpacking
-
Cut the straps, then lift the box over the unit and unpack.
-
Carefully remove all parts from the carton and inspect for any damage or missing parts. If parts are damaged or missing, contact your dealer immediately.
-
Locate the hardware package. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the item number from the assembly drawing for reference.
Tools and Parts Included
| Tools Included |
| 5mm L-Allen Wrench |
| 6mm L-Allen Wrench |
| 8mm L-Allen Wrench |
| 12/14mm Wrench |
| 13/14mm Wrench |
| Phillips Screwdriver |
| Short Phillips Screwdriver |
| Parts Included | |
| Quantity | Part Name |
| 1 | Main Frame |
| 2 | Foot Pedal |
| 1 | Seat Cover |
| 1 | Connecting Arm |
| 1 | Console Mast |
| 1 | Console Mast Cover |
| 1 | Water Bottle Holder |
| 4 | End Caps |
| 2 | Transport Wheel |
| 1 | Seat |
| 1 | Seatback Frame |
| 2 | Swing Arm |
| 1 | Console |
| 1 | Hardware Kit |
| 1 | Power Cord |
| 1 | Audio Cable |
CRS800S Step-by-Step Assembly
1. Pedals, Seat Bottom, Handgrips/Handlebars
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #203 | Hex Head Bolt | 3/8" x 3-1/4" | 2 |
| #201 | Hex Head Bolt | 3/8" x 2" | 4 |
| #202 | Hex Head Bolt | 5/16" x 1-1/4" | 1 |
| #155 | Phillips Head Screw | M5 x 15 | 12 |
| #204 | Flat Washer | 3/8" | 8 |
| #205 | Flat Washer | 5/16" | 2 |
| #206 | Nyloc Nut | 3/8" | 6 |
| #161 | Nyloc Nut | 5/16" | 1 |
a. Secure the pedals to the pedal plates with six Phillips Head Screws (#155) each.
b. Use a Hex Head Bolt (#202), two Flat Washers (#205), and a Nyloc Nut (#161) to secure the locking gas piston on the seat bottom.
c. Install Seat Cover (45).
d. Use two Hex Head Bolts (#203) with two Flat Washers (#204) and two Nyloc Nuts (#206) to secure the handgrip.
e. Use four Hex Head Bolts (#201), four Flat Washers (#204) and four Nyloc Nuts (#206) to secure the handlebar to the seat assembly.
f. Connect the hand pulse cables; arrange cables taking care so they are not crushed during seat rotation and adjustment.
2. Console Mast
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #209 | Button Head Bolt | 5/16" x 1-3/4" | 2 |
| #207 | Hex Head Bolt | M8 x 16 | 2 |
| #208 | Hex Head Bolt | 3/8" x 2-1/2" | 2 |
| #169 | Flat Washer | 3/8" | 2 |
| #210 | Curved Washer | M8 | 2 |
| #206 | Nyloc Nut | 3/8" | 2 |
| #161 | Nyloc Nut | 5/16" | 2 |
| #211 | Split Washer | 1-3/8" | 2 |
| #245 | Flat Head Socket Screw | M8 x 1.25 x 30L | 6 |
| #246 | Square Nut | M8 x 1.25 x 6.5T | 6 |
a. Install the transportation wheels (87) with the Button Head Bolts (#209) and Nyloc Nuts (#161).
b. Place the console mast (2) through the console mast cover (#76) with the correct orientation. Snake the computer cable through the bottom end of the console mast and out through the top.
c. Insert the mast on the main frame and use Hex Head Bolts (#208) with Split Washers (#211), Flat Washers (#169) and Nyloc Nuts (#206) to secure on the side. Then use Hex Head Bolts (#207) and Curved Washers (#210) to secure at the front and back of tube.
d. Plug in the end caps (67) on oval stabilizer tubes. NOTE: Do not pinch wires.
e. Secure the handle sliders (7, 8) using three Flat Head Socket Screws (#245) and three Square Nuts (#246) on each side.
f. Clamp the water bottle cage (111) to either handlebar.
3. Seat
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #145 | Hex Head Bolt | M6 | 4 |
| #172 | Flat Washer | 3/8" | 2 |
| #206 | Nyloc Nut | 3/8" x 7 | 2 |
| #212 | Hex Head Bolt | 3/8" x 1-3/4" | 2 |
a. Insert the seat back (36) in the seat carriage and secure with Hex Head Bolts (#212), Flat Washers (#172) and Nyloc Nuts (#206).
b. Put the seat cushion (35) on the seat carriage and secure with Hex Head Bolts (#145).
4. Computer Cables
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #155 | Phillips Head Screws | M5 x 12 | 4 |
| #213 | Button Head Bolt | 3/8" x 3/4" | 12 |
| #214 | Flat Washer | 3/8" x 19 x 1.5 | 4 |
| #215 | Curved Washer | 10 x 21.3 x 7.8T | 8 |
| #216 | Split Washer | 10 x 2T | 12 |
a. Connect the computer cables from the mast to the console (27) and use Phillips Head Screws (#155) to secure it.
b. To install the left and right swing arms (4, 3) onto the main frame use Button Head Bolts (#213), Flat Washers (#214), Split Washers (#216) and Curved Washers (#215).