Pre-Assembly
Please read before unpacking your treadmill. Serious injury could occur if this treadmill is not unpacked properly.
Unpacking
- To remove the treadmill safely from its packaging, cut the straps along the dotted line on the bottom of the box. Lift the box over the unit and unpack.
- Locate the hardware package. The hardware is separated into four (4) steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the item number from the assembly drawing for reference.
Tools and Parts Included
| Tools |
| 3/8" Allen Wrench |
| 10mm Allen Wrench |
| Phillips Screwdriver |
| Parts Included | |
| Quantity | Part Name |
| 2 | Console Masts |
| 2 | Side Covers |
| 1 | Base Frame |
| 1 | Console Support |
| 1 | Console |
| 1 | Safety Key |
| 1 | Power Cord |
| 1 | Tube of Lubricant |
| 1 | Hardware Kit |
Step-by-Step Assembly Instructions
1. Uprights
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #116 | Flat Washer | 3/8" x 3.5 x 2T | 10 |
| #117 | Split Washer | 3/8" x 16.5 x 2.0T | 10 |
| #134 | Screw | M5 x 12mm | 4 |
| #144 | Bolt | 3/8" x 3" | 10 |
a. The right upright (34) has a preinstalled lower computer cable (42), TV signal (153), console power (155), network (157), CSAFE (159), and HDMI cable (161). To install the uprights on the base frame, special care must be taken not to pinch the computer cable between the upright and frame base. Slide the split washer (#117) and flat washer (#116) on the button head socket bolt (#144). Slide the bolt through the top hole in the retaining plate (98), and corresponding top hole in the upright tube, and screw into the base frame. Now install the other four button head socket bolts (#144) together with split washers (#117), and flat washers (#116) and tighten all five bolts.
b. Repeat the previous step to install the left upright (33).
c. Attach the left and right plastic covers (26-L, 27-R) with four Phillips head screws (#134).
2. Computer Cables
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #133 | Screw | M5 x 20 | 4 |
a. Connect the upper computer cable (41), TV signal (152), console power (154), network (156), CSAFE (158), and HDMI cable (160), hand pulse wire (39, 40) and ground wire (162) to the board on the back of the console (28).
b. Use four Phillips head screws (#133) to secure console assembly to the console support (5).
3. Console Support
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #117 | Split Washer | 3/8" x 16.5 x 2.0T | 6 |
| #125 | Flat Washer | 3/8" x 25 x 2T | 6 |
| #145 | Bolt | 3/8" x 3/4" | 6 |
| #146 | Bolt | M8 x 12 | 6 |
a. Use six socket head cap bolts (#146) to secure the console onto the left and right mounting brackets (3-L, 4-R). When assembling the console mounting interface brackets, please be sure to slide the brackets all the way toward the back of the console before tightening the bolts.
b. Connect upper computer cable (41) and lower computer cable (42), upper TV signal cable (152) and lower TV signal cable (153), upper console power cord (154) and lower console power cord (155), upper network with cable (156) and lower network with cable (157), upper CSAFE with cable (158) and lower CSAFE with cable (159), upper HDMI cable (160), and lower HDMI cable (161). Slide the assembly into the left and right uprights.
c. Slide six split washers (#117) and six flat washers (#125) onto six button head socket bolts (#145) on top of uprights. Be careful not to pinch the cable.
4. Attach the Console
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #117 | Split Washer | 3/8" x 16.5 x 2.0T | 2 |
| #162 | Bolt | 3/8" x 16 x 1-3/4" | 2 |
| #163 | Curved Washer | 10 x 23 x 1.5T | 2 |
a. Slide two curved washers (#163) and two split washers (#117) onto two button head sockets bolts (#162). Slide the bolts through the holes on the console masts and tighten.