Pre-Assembly
Please read before unpacking your treadmill. Serious injury could occur if this treadmill is not unpacked properly.
Unpacking
-
To remove the treadmill safely from its packaging, cut the straps along the dotted line on the bottom of the box. Lift the box over the unit and unpack.
-
Locate the hardware package. The hardware is separated into four (4) steps. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the item number from the assembly drawing for reference.
Tools and Parts Included
Tools |
3/8" Allen Wrench |
10mm Allen Wrench |
Phillips Screwdriver |
Parts | |
Quantity | Part Name |
2 | Console Mast |
2 | Side Cover |
1 | Base Frame |
1 | Console Support |
1 | Console |
1 | Safety Button |
1 | Power Cord |
1 | Hardware Kit |
Step-by-Step Assembly Instructions
1. Uprights and Computer Cables
Hardware Needed for This Step | |||
PART | TYPE | DESCRIPTION | QUANTITY |
#150 | Button Head Socket Bolt | 3/8" x 3" | 10 |
#133 | Split Washer | 10 x 2.0T | 10 |
#115 | Flat Washer | 3/8" x 35 x 2.0T | 10 |
#144 | Phillips Head Screw | M5 x 12mm | 4 |
a. Gather all hardware needed for this step.
b. Thread the computer cable (53) up through the center of the right upright column (9).
c. Use four (4) sets of button head socket bolts (#150), split washers (#133) against a flat washer (#115) to secure the upright fixing plate (10) to the right upright (9) to the main frame (1) using the Allen wrench (160).
d. Use two (2) Phillips head screws (#144) to secure the right motor base cap (35) to the main frame (1) using the screwdriver (158).
e. Repeat step C-D on the left side.
2. Console Computer Cables
Hardware Needed for This Step | |||
PART | TYPE | DESCRIPTION | QUANTITY |
#152 | Socket Head Cap Bolt | M8 x 12mm | 6 |
#153 | Flat Washer | 8 x 16 x 2T | 6 |
#151 | Button Head Socket Bolt | 3/8" x 3/4" | 6 |
#133 | Split Washer | 10 x 2T | 6 |
#125 | Flat Washer | 3/8" x 25 x 2.0T | 6 |
a. Gather all hardware needed for this step.
b. On the underside of the console (5) is where the locking plate assembly (3, 4) can be attached. Use three socket head cap bolts (#152) and three flat washers (#153) on each side to secure.
c. Connect the computer cable (53) with the upper computer cable (52). Be careful not to pinch the wires. Slide them into the right upright (9).
d. Gently slide the console (5) into the left and right uprights (8, 9) and secure with three button head socket bolts (#151), three split washers (#133), and three flat washers (#125) on both sides using the Allen wrench (160).
3. Secure the Console
Hardware Needed for This Step | |||
PART | TYPE | DESCRIPTION | QUANTITY |
#154 | Button Head Socket Bolt | 3/8" x UNC16 x 1-1/4 | 2 |
#133 | Split Washer | 10 x 2T | 2 |
#155 | Curved Washer | 10 x 23 x 1.5T | 2 |
#29 | Round Cap | 1 |
a. Gather all hardware needed for this step.
b. Further secure the uprights by inserting a button head socket bolt (#154) through a split washer (#133), and a curved washer (#155) onto the backside of both left and right uprights (8, 9) using the Allen wrench (160).
c. Plug the round cap (#29) into the right upright (9).
d. Plug the safety key (72) into the safety key base on the console (5).
4. Console Display and Handpulse Wires
Hardware Needed for This Step | |||
PART | TYPE | DESCRIPTION | QUANTITY |
#156 | Socket Head Cap Bolt | M8 x P1.25 x 20L | 4 |
#120 | Split Washer | 8 x 1.5T | 4 |
#153 | Flat Washer | 8 x 16 x 2T | 4 |
#144 | Phillips Head Screw | M5 x 12mm | 2 |
a. Gather all hardware needed for this step.
b. Place the console display (38) onto the console (5). Secure with four socket head cap bolts (#156), four split washers (#120), and four flat washers (#153) using the Allen wrench (159).
c. Connect the upper handpulse wires (50, 51) and upper computer cable (52) to the console display (38).
d. Fasten the console cover (41) with one Phillips head screw (#144) to the console (5) using the screwdriver (158).