Pre-Assembly
Please read before unpacking your treadmill. Serious injury could occur if this treadmill is not unpacked properly.
Unpacking
- To remove the treadmill safely from its packaging, cut the straps, then lift the box over the unit and unpack.
- Carefully remove all parts from the carton and inspect for any damage or missing parts. If parts are damaged or missing, contact your dealer immediately.
- Locate the hardware package. Remove the tools first. Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the item number from the assembly drawing for reference.
Tools and Parts Included
| Tools |
| Phillips Head Screwdriver |
| L Allen Wrench |
| Combination M5 Allen Wrench & Phillips Head Screwdriver |
| Parts | |
| Quantity | Part Name |
| 1 | Main Frame |
| 2 | Upright |
| 2 | Frame Base Cover |
| 2 | Console Mast Cover |
| 1 | Console |
| 1 | Deck |
| 1 | Beverage Holder |
| 1 | Audio Cable |
| 1 | Power Cord |
| 1 | Hardware Kit |
Step-by-Step Assembly Instructions
1. Uprights and Computer Cables
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #100 | Bolt | 5/16" x 3/4" | 4 |
| #124 | Curved Washer | 8 x 23 x 1.5T | 4 |
| #123 | Bolt | 3/8" x 2-1/2" | 6 |
| #79 | Flat Washer | 3/8" x 19 x 1.5T | 6 |
| #86 | Spring Washer | 10 x 2.0T | 6 |
a. Gather all hardware needed for this step.
b. Slide the left and right upright covers (L-52, R-53) onto the left and right uprights (4, 5).
c. Slide the console mast side caps (L-98, R-99) onto the left and right uprights (4, 5) under the upright covers.
d. Connect the lower computer cable (33) to the middle computer cable (32). Be sure not to pinch the cable or damage may occur.
e. Insert the left and right uprights into the main frame (1) and use the combination wrench and Phillips head screwdriver (103) to secure four bolts #(100) and four curved washers (#124) into place.
f. Use the L-shaped Allen wrench (104) to tighten the left and right gusset (7, 8) with six bolts (#123), six flat washers (#79), and six spring washers (#86).
2. Secure Console Mast Side Caps
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #127 | Phillips Head Screw | M5 x 10mm | 4 |
a. Gather all hardware needed for this step.
b. Install the console mast side cap (L-98, R-99) onto the main frame (1) and secure it using four screws (#127) by using the combination wrench and Phillips head screwdriver (103).
3. Attach the Console
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #91 | Bolt | 3/8" x 1-3/4" | 4 |
| #86 | Split Washer | 10 x 2.0T | 4 |
a. Gather all hardware needed for this step.
b. Connect the speed adjustment switch and cable (37) with the upper speed cable (34).
c. Connect the incline adjustment switch and cable (38) with the upper incline cable (35).
d. Connect the middle computer cable (32) to the upper computer cable (31). Be sure not to pinch any of the cables or damage may occur to the system.
e. Insert the console (36) onto the right and left uprights (4, 5) and secure with four button head socket bolts (#91) and four split washers (#86). Use the Allen wrench (107) to tighten.
4. Secure Console Mast Covers
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #125 | Sheet Metal Screw | 3.5T x 16mm | 8 |
a. Gather all hardware needed for this step.
b. Slide right and left console mast covers (53, 52) up the uprights. Secure them with eight sheet metal screws (#125) using the Phillips head screwdriver (126).
5. Handrails
| Hardware Needed for This Step | |||
| PART | TYPE | DESCRIPTION | QUANTITY |
| #100 | Bolt | 5/16" x 3/4" | 4 |
a. Gather all hardware needed for this step.
b. Place the handrail support (3) between the left and right uprights (5, 4) and use the combination Allen wrench and Phillips head screwdriver (103) to tighten four button head socket bolts (#100).
c. Place the beverage holder (120) onto the handrail support (3).